| View previous topic :: View next topic |
| Author |
Message |
Spikeophant Member
Joined: 12 Mar 2010 Posts: 164 Location: Bend, Oregon
1986 Chevrolet Camaro IROC-Z
|
Posted: Thu Apr 15, 2010 7:46 am Post subject: Bad Bearing? |
|
|
So, I have a noise under my hood, sounds like it's coming from the accessories, that sounds like a bad bearing. I put a stethescope on all my accessories, and it sounded like the alternator had a bad bearing, it was making a whine and a clunk, so I swapped it out. Still making the noise. I noticed some play in the shaft for the water pump, that the pulley mounts to, so that's the next likely culprit, but it didn't make much noise when I put a stethescope on it. Any ideas on other things to check, I am hoping it's not a bad crank bearing, or I shouldn't have paid 3k for the car. I have put around 3k on it since I bought it, and it's made the noise the whole time, I was just pretty sure it was a bad alternator bearing. _________________ 1986 Camaro Z-28 IROC-Z 350 swap |
|
| Back to top |
|
 |
izcain 9sec Club
Joined: 09 Sep 2006 Posts: 1306 Location: Port Angeles WA
1983 Chevrolet Camaro Z/28
|
Posted: Thu Apr 15, 2010 8:20 am Post subject: |
|
|
Tensioner? have you listened to it? Seen alot of good components replaced when it was just a simple pulley tensioner making noise and/or worn out. _________________
1983 Z28 383 + 201ci more = New Heart for this season!
9.17 @ 148 |
|
| Back to top |
|
 |
Spikeophant Member
Joined: 12 Mar 2010 Posts: 164 Location: Bend, Oregon
1986 Chevrolet Camaro IROC-Z
|
Posted: Thu Apr 15, 2010 8:30 am Post subject: |
|
|
I don't have any tensioners, I have a belt for every accessory, cars had a 350 swapped in, I have some docs showing the engine swap 25k ago. _________________ 1986 Camaro Z-28 IROC-Z 350 swap |
|
| Back to top |
|
 |
Twilightoptics Hardcore (12sec Club)

Joined: 13 Jan 2004 Posts: 9191 Location: Auburn , WA
1987 Chevrolet Camaro IROC-Z
|
Posted: Thu Apr 15, 2010 2:41 pm Post subject: |
|
|
Pull the belts off one at a time then and see where the sound goes away. _________________ A redline a day keeps the carbon away! |
|
| Back to top |
|
 |
Spikeophant Member
Joined: 12 Mar 2010 Posts: 164 Location: Bend, Oregon
1986 Chevrolet Camaro IROC-Z
|
Posted: Thu Apr 15, 2010 2:45 pm Post subject: |
|
|
Gonna do the water pump this weekend, I'll figure it out for sure then, I can watch the water pump pulley wobble around slightly, and it had almost a full 1/8th inch of play, up and down. I'm about 100% it's that now.  _________________ 1986 Camaro Z-28 IROC-Z 350 swap |
|
| Back to top |
|
 |
Alphius Peanut

Joined: 05 Sep 2006 Posts: 2429 Location: Grand Mound
1984 Chevrolet Camaro Z/28
|
Posted: Thu Apr 15, 2010 5:53 pm Post subject: |
|
|
I bought a TPI Trans Am not too long ago for $500 because the owner thought it had a bad rod knock. It had a bad water pump bearing that was rattling around. New waterpump, good as new!
Sounds like you got it nailed. The T/A waterpump I had was loose and floppy like yours and made tons of noise as well. _________________ 84 Camaro Z28 - LS1/T56
85 Silverado - Low and Slow |
|
| Back to top |
|
 |
|